Renewable Energy

Emulsion layer limits screen-printing damage in copper-plated HJT solar cells

Marisol QuinteroNovember 15, 20265 min read1 views

At a glance

  • A Chinese research team links screen-mesh knuckle wear to efficiency loss and finds a 4.7% emulsion coverage pattern offers the best protection–uniformity trade-off.
  • Researchers in China have identified progressive screen-mesh knuckle wear as a main cause of degradation in copper-plated HJT solar cells and developed an emulsion buffer layer to reduce direct mesh–wafer contact. In tests, 4.7% emulsion coverage limited minority carrier lifetime degradation to 0.41% after 10,000 printing cycles while maintaining relatively good photoresist coating uniformity.
A conceptual close-up shows a screen-printing mesh suspended over a solar cell wafer, with an emulsion layer separating the mesh from the wafer surface.

Screen printing is widely used for solar cell metallization, but the mechanical and thermal demands of the process can degrade sensitive device structures. The issue is especially important for copper-plated silicon heterojunction (HJT) solar cells, which are being pursued as a way to lower metallization costs and reduce reliance on silver.

Researchers in China have investigated how screen printing causes degradation in copper-plated HJT cells and developed a method to mitigate it. Their work focused on the photoresist-printing step and on the cumulative damage that occurs as screens are used repeatedly in production.

Efficiency loss traced to screen wear

Previous investigations cited by the researchers showed conversion efficiency falling from 26.2% to 25.7% over 15,000 consecutive printing cycles in commercial solar cell production. The losses were mainly attributed to reductions in open-circuit voltage and fill factor, while short-circuit current density and electrical resistance remained largely unchanged. Minority carrier lifetime degradation rose from 0.61% with a new screen to 11.0% after 15,000 printing cycles.

Using three-dimensional confocal microscopy, the scientists identified progressive wear of the screen mesh knuckles as the main cause. As the knuckles wore down, their contact area with the wafer increased, placing greater mechanical stress on the underlying passivation layers. Scanning electron microscopy showed no visible surface scratches, but photoluminescence measurements indicated increased recombination losses, suggesting damage to the amorphous silicon/crystalline silicon interface.

Why photoresist printing is different

Corresponding author Lang Zhou said the screen-printing process for photoresist application in HJT cells differs fundamentally from conventional silver-paste printing. In silver-paste printing, screen openings account for only 2–5% of the total area, while an emulsion layer covers the rest and prevents direct contact between the mesh and the wafer. Full-area photoresist coating typically uses a screen without emulsion coverage to ensure uniform resist deposition across the wafer. As a result, the mesh comes into direct and extensive contact with the wafer during each printing cycle.

Emulsion buffer limits damage

To address the issue, the researchers developed an emulsion buffer layer intended to prevent direct contact between the screen mesh and the wafer surface. They evaluated six patterns with emulsion coverage ratios ranging from 2.9% to 16.6%.

The results revealed a trade-off between mechanical protection and photoresist coating uniformity: higher emulsion coverage reduced damage but impaired ink distribution. An emulsion coverage ratio of 4.7% provided the best balance, limiting minority carrier lifetime degradation to 0.41% after 10,000 printing cycles while maintaining relatively good coating uniformity.

The researchers attributed the improvement to the emulsion layer preventing direct mesh–wafer contact, thereby reducing cumulative mechanical damage to the passivation layers. Zhou said the findings show that a relatively simple modification to screen design can substantially mitigate printing-induced degradation, offering a practical approach to improving manufacturing reliability for copper-plated HJT cells.

The results were presented in “Screen-printing photoresist induced efficiency degradation and mitigation in Cu-plated SHJ solar cells,” published in Solar Energy.

Copper metallization gains attention

The work comes amid growing interest in copper metallization as an alternative to silver contacts in HJT solar cells. In April 2026, researchers at China’s Nankai University developed a silver-free HJT solar cell with 25.2% efficiency using plasma-induced interface engineering and copper electroplating. The approach addressed adhesion, contact resistance and stability challenges at the ITO interface.

Separately, scientists at Germany’s Forschungszentrum Jülich achieved 23.08% efficiency in a fully copper-metallized HJT solar cell. The silver-free device showed a relatively small efficiency penalty compared with its silver-metallized counterpart, while cells combining silver-copper paste on the front side with silver contacts on the rear reached 23.95% efficiency. The findings underline copper’s potential to reduce silver consumption, although further improvements in processing and electrical performance are still needed.

Reported by Marisol Quintero, Grid Integration and Energy Monitoring Editor.